Infants and toddlers have died in cribs with makeshift repairs. The cribs were manufactured in China. This warranty covers 1 year from the date oforiginal purchase. Before you can get into the fun part of decorating the baby's nursery, you need to know the baby has a safe place to sleep and it's impossible to know that a crib is put together properly without the owner's manual. Slide the moving drawer into the crib as shown.
Be sure side is raised and locked position whenever child is in crib. Click Ok if you wish to continue to the website; otherwise, click Cancel to return to our site. If not, use the Allen key to remove bolts and lower the mattress support into the lowest position shown in diagram 18. Place the assembled piece from diagram 6 15 Top down on a non-abrasive surface, such as carpet. Federal law bars any person from selling products subject to a publicly-announced voluntary recall by a manufacturer or a mandatory recall ordered by the Commission.
These bolts will need to be adjusted up or down to allow for connection to bed rail. You will need to know the brand as well as other information see the next paragraph before you begin your search for a manual. Back a D 38 7 A11 7 b Back 7 FrontLeft Right24. Use the short end of the Allen wrench for final tightening. The drop-side failures result from both the hardware and crib design, which allow consumers to unintentionally install the drop-side upside down. Tightly fasten the Allen bolts with Allen wrench A. As your child grows and is able to stand, mattress support must be lowered.
Tighten the bolts with hands. . This warranty is valid only upon presentation of proof of purchase. To protect your floor and the crib legs after pulling the large casters 35 out of the crib, make sure the plastic sheaths are on the crib posts. Tightly fasten the Allen bolts with Allen wrench A.
Note: Please keep assembly instructions and the remaining hardware and parts for future use. J Note: Make sure the grooves on the side panels and back panel are lined up. Tightly fasten the screw J with Philips head screwdriver not included. A damp cloth may be usedoccasionally to clean surface. Diagram 8 Note: The groove on the top middle crossbar 15 should be facing bottom, the grooves on the bottom middle crossbar 16 should be facing up and back, the grooves on the top crossbars 14 should be facing inside of the changer.
They may have the crib instruction manual that you are looking for and be willing to scan and mail or email it to you; it never hurts to ask. Attach the small casters 36 to the bottom end of the moving 31 drawer posts 31 as shown in instruction a. Set the assembled unit aside for later assembly steps. This, in turn, can weaken the hardware and cause the drop-side to detach from the crib. These cribs pose a risk of serious injury or death due to entrapment, strangulation, suffocation and fall hazards to infants and toddlers. Estimated assembly time is two and a half hours when 2 people are assembling. Please read the Assembly Instructions prior to assembling this product.
Are you ready to put the crib together only to find that the crib instructions are missing? Please wait until all steps arecompleted before tightening bolts. Place the crib from diagram 19 down on a non-abrasive 35 Plastic switchsurface such carpet. The crib and changer combo is now ready for use. Unclamp the Allen bolts with Allen wrench A to remove the crib front frame 10. Care: Wipe with a damp cloth. Tightly fasten the Allen bolt with Allen wrench A. Set the assembled unit aside for later assembly steps.
Tightly fasten the Allen bolts with Allen wrench A BackDiagram 10 a b N N7 7 Top 6 7 Bottom 13. Moving Drawer Side Panel 29. Remove the large casters 35. This is solelylimited to the repair or replacement of defective furniture components and no assembly labor isincluded. This recall includes fixed-side and drop-side cribs.
Excessive exposure to sunlight and extreme changes in temperature and moisture can damage woodfurniture. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Make sure warnings are always visible. So, where can you get those crib assembly instructions? Attach the second moving drawer side frame from diagram 21 to the assembled piece from step 33 using large screws J as shown in instruction a. This warranty givesyou specific legal rights and you may also have other rights which vary from State to State. Please see our Affiliate Disclosure page for more information. Any disengagement can create a gap, which could fatally entrap a child.